Some application program does not display the image clearly if the image is too small. Specification of the application program. Scan quality is poor (Poor image displayed on the monitor) In the confirmation dialog, click the button ( button for Macintosh). To delete a link to a program, click the button. Even if it could be linked, it may not work in some cases. Some shortcuts or aliases of certain application programs cannot be linked. Some application programs linked to the CanoScan Toolbox may not work. You can link a program by dragging and dropping an executable file or its shortcut/alias from its folder on the desktop (or the Start menu for Windows) into the box. Ensure that you select an executable file. Please note that folders may also be represented by icons. Click or double-click the icon to confirm in advance that it starts the intended program. Since file extension names are not appended by Macintosh systems, you must find the executable file by searching for the file icon.
Most application programs are contained within a folder labeled with its name or the software manufacturer's name inside the folder.
If file name extensions are set not to display, open the Windows Explorer, select the menu, followed by and the tab, and remove the check mark from the option. Double-click the file to confirm in advance that it starts the intended program. The file name extension is always appended to an executable file*. The program file you choose must be an executable file. To link a different program, click the button (Windows) or button (Macintosh), select the program you wish to use, and click the button. You can link a different program to the scanner button by changing the CanoScan Toolbox settings. The application programs linked to the scanner buttons are managed by CanoScan Toolbox. The application programs linked to the scanner buttons are changed.
When pressing a scanner button (COPY, SCAN, PDF (CanoScan LiDE 60 only) or E-MAIL button), another application program starts įor each scanner button, remove check marks from application programs other than the intended program in the "Send to this application:" list and click the button.Ĭlick the button when the settings for each scanner button are complete.įollow the instructions in "To Link a Different Program" described in Symptom 13. Steps may vary slightly for other Windows versions).Ĭlick the menu, followed by, and the icon. Reset the scanner button assignments with the following procedures (For Windows XP. Software programs were not installed according to the Quick Start Guide instructions or the settings have been altered for some reason. "Choose Application" dialog displays when a scanner button (on the scanner) is pressed When pressing a scanner button (COPY, SCAN, PDF (CanoScan LiDE 60 only) or E-MAIL button), the scanner does not scan an imageĬheck the settings of the scanner button function of CanoScan Toolbox. Multiple devices connected to the USB port.ĭisconnect all other devices but the scanner from the port.
Open ScanGear CS from within the application program, click the button in the Advanced Mode, and change the folder listed in the category to one on a disk with sufficient free space.įor CanoScan Toolbox, click the button and change the folder listed in the category to one on a disk with sufficient free space. Reset and reboot the computer, delete unnecessary files and application programs, and rescan. Reboot the computer, lower the Output Resolution and rescan. Then reconnect the USB interface cable to the computer. Select your scanner following the directions in Scanning with ScanGear CS in Initiating a Scan.Īn error message "Release the lock switch" appears and ScanGear CS fails to previewĬlose the software programs, disconnect the USB interface cable from the scanner and set the scanner's lock switch to the unlocked position. Attach the cable to a USB port on the computer itself (not the hub). If a USB hub is used for the connection, do not use it. Only use the USB cable that was supplied with the scanner.Īttach the USB cable to a different USB port on the computer itself (not a hub).
ScanGear CS already running as a scanner driver within another application program.Īn error message, such as "Cannot communicate with scanner." appears and the ScanGear CS window fails to appear Insufficient memory (RAM) available to start ScanGear CS.Ĭlose other programs and start ScanGear CS. Start ScanGear CS from within a TWAIN compatible program. The Feature of the application program does not support calling up ScanGear CS. Scanner driver (ScanGear CS) not installed. CanoScan LiDE 25/LiDE 60 Scanning Guide Problems with Scanning